INSTALLING A BATH TUB

Installing A Bath tub

Installing A Bath tub

Blog Article

Book Maintenance

Are you trying to locate insight about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


How to Install a Bathtub Yourself
Installing a bathtub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also often, tiling abilities. Changing an old tub with a new one is also a moderately difficult task. If the old bathtub is conveniently easily accessible, the job can move rapidly; if you have to open a wall to get rid of the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified yourself for the work as well as are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed task, it is much better to think about employing one prior to you begin. Chances are you might require a professional plumber to make tube links.
This post will certainly assist you install a brand-new tub in your bathroom if you have actually already bought a brand-new tub and also do not need to transform the plan of your previous water supply pipelines.
Your tools and also material checklist must comprise the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing faucets can be fairly troublesome as a result of the restricted access that is commonly the case.
    Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
    Before moving on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existent supply pipes.
    If you require to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in area in between the faucet and the sink. Secure the tap in place with the producer supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.

    Setting up the Tub


    Using the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
    The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the spirit level reviews degree.
    To set up taps, fit the bottom of the outermost adaptable faucet port to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
    Activate the water system and check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the bathtub and additionally inspect the overflow outlet and also the typical outlet for leakages.
    Ultimately, repair the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will resolve it into its final placement.

    Preparing for the Installment


    First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the faucet features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
    Fit the flexible faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use every one of the provided washers.
    Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last position.

    Tiling Around the Tub


    In the location where the bathroom meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall between the bathroom and also the tiling, bring about complications with dampness as well as possible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealants to blend in your fixtures and fittings. They are offered in tubes as well as cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can split rather very early if you do not think about this activity prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I ran across that article on How to Install a Bathtub Yourself when browsing on the search engines. Remember to take a moment to distribute this blog if you liked it. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.




    Request Estimate


    Report this page